Accelerating pace with technology development, and in many public places, you'll find the floor scrubbing machine has been replaced by artificial, in a way that the machines greatly liberating the productive forces, some say, is the laziest man in the world scientists, because there's a lot of invention in life are greatly facilitates people's lives. Maintains cleanliness the profession is accompanied by the development of the service sector and derived industries, fully automatic washing machine uses in maintaining cleanliness industry is be a revolution! How to maintain a clean washing machine appears to be a very important thing. The following describes which parts washing machines are how to clean the washing machine!

1 Water grill
1. Check floor scrubbing machine water Grill in the tape residue inside, out in a timely manner. 2. Check the water grill stripes are damaged, damaged affect the seal, causing the water not completely clean. 3. Check the water to get contact with the ground and the level of parallelism, good water grill should be parallel to the ground after landing, symmetrical. If not, adjust the angle of the water grill. For correct use, water grill should be based on the wear of plastic to adjust its height in the process of cleaning, rubber strip in the length direction should be back after bending 5mm. 4. Check whether the suction motor switch is turned on

2 Brush plate
The floor scrubbing machine wear of the brush plate removed a look at brush plate if you are using the hundred - cleaning pad was also set to pin down, if a length less than 1.5cm should be replaced when brushing brush plate. Hundred - cleaning pad wear to a 1.0cm replace the new hundred - cleaning pads, if oil from the ground when too much, please add in addition to oil, which can effectively remove the oil.

YHCX5070 NKR77LLPACJAY chassis-mounted vacuum road sweeper adopts pure suction airflow dry type operations, and it is especially developed for urban roads conditions. This model sweeping width is 2.4m to 2.8m, with 5 m3 waste hopper, auxiliary suction pipe(6-10m) and high efficient spray dust suppression device. The center vacuum disk can effectively remove waste from tens of microns to the leaves, gravel, stones, bricks,etc. The auxiliary suction hose’s working diameter can reach 10m, which can used for green belt and blind corner manual work can’t reach. No secondary dust problem, and the sweeping rate up to 99% or more.It can be widely used for road cleaning, moreover, it is the ideal sanitation equipment for the places of square, park, campus, housing area, parking lot, dock, airport, cement plant, electric power plant, steel plant, etc.

YHCX5070 NKR77LLPACJAY chassis-mounted vacuum road sweeper Features:
1、Simple Structure: No hydraulic motor Slewing Mechanism, no sweeping brushes system
2、Easy operation: Only through the control panel in Cab, the operator can control the auxiliary engine’s on/off, fan speed’s up/down, dust sucking mouth’s up/down, rear door’s open/close, waste hopper’s lift/fall, water spray’s on/off.
3、No secondary dust: Pure suction type, no reverse blow, adopt unique, advanced, high efficient filter system
4、Low working cost: No sweeping brush frequent replacement, just bits of rubber wearing parts. It need low maintenance cost every year.
5、Excellent dust removal efficiency: Garbage collected into the hopper, after several times of dust, through multi-stage gravitational fallout and inertial dust particles achieve dust separation, afford to keep them truly suck up and stay. In addition, with independent research and patented dry dust cleaning device, it can achieve automatic high performance cleaning, without staff participation (suitable for place of heavy dust).
6、Strong adaptability: Equipped with an infrared camera, long duration, regardless of day or night, rain, wind or the cold of winter, it can also be used as usual, reflecting the all-weather, all-day job of the design concept.
7、Improving the cleaning efficiency, reducing the cost of cleaning: One suction sweeper vehicle is equal to more than 30 cleaners, saving the cost of labor and personnel management, while also saving the cost of cleaning equipments purchase.

The YHFS-750R ride on floor Scrubber Drier is the generation of scrubber/driers, with focus on performance, ergonomics and reliability. Low sound level, making daytime cleaning possible in sensitive areas, outstanding traction of efficient double scrubbing tasks, and excellent drying efficiency.The YHFS-750R is simply the better choice.

Ride On Floor Scrubber Drier YHFS-750R Features:
1. Turn flexible.
2. Clean and dry going either forward or backwards.
3. It is perfect choice for heavy-duty cleaning such as entryways, spill cleanup, grease removal, grout and porous-surface cleaning etc.
4. User friendly, the one touch control panel is compact designed while the more effective performance. All switches are indicated by chart, easy operate and high productivity.
5. Flexible only 100cm turn-around aisle width ensures the machine to suit for more environments.
6. Easily assembled and maintained with lowest running cost, excellent performance gives the safe and smooth operation to the user.
7. Large-capacity battery enables it to work continuously for long time.
8. Clean stubborn dirt, grime, greases, and oils.
9. Aluminum squeegee assembly and scrub heads, shock-absorbing frame and durable polyethylene construction for long machine life
10. ec-H2O and FaST technologies use 70% less water and clean up to three times longer with a single tank of water
11. Adjustable , ergonomic paddle handle provides comfort and safety.
12. Simple control panel design give quick access to variable scrub pressure, ECO solution system, and click-off scrub head system.

This Battery Ride On Sweeper is designed with double powers, dry and wet sweeping. Double powers are micro generator and Lithium-Ion battery.

Battery Ride On Sweeper YHB16 Features:
1. Power system: this electric sweeper is designed with double powers, dry and wet sweeping. Double powers are micro generator and Lithium-ion battery. These two powers can drive sweeper travel and work separately. In order to save energy and reduce exhaust the generator is only for emergency condition. When the battery is dead, start generator to drive sweeper work, meanwhile charge battery.
2. Control system: the sweeper is concentrative controlled by micro computer.
3. Steering system: electric steering structure, front and rear frame is connected by hinge, the operation of control steering is very simple, small turning radius. (has applied patent)
4. Suction device: it is designed with electric high speed blower and high efficiency suction port, which save energy and transport garbage into dustbin favorably. (has applied patent)
5. Dust removing style: the dust removing device with centrifuge, static electricity, filter and impulse which ensure the exhaust air does not has second pollution. (has applied patent)
6. Dumping style: the dumping style adopts high post dumping structure, and the dump can be operated by remote control. (has applied patent)
7. Electric heater: the target is to improve technology and offer an electric heater with simple structure, heat transfer need not any refrigerant, can work on end, cooling and heating are integrative, cooled and heated time is very short, can offer heating whether engine offer heat source or not. (has applied patent)
8. Environmental protection, save energy, silent: this electric sweeper changes the design concept of traditional sweeper. New structure has the features of high transmission efficiency, small size, simple structure, saving energy, low exhaust and noise, this sweeper is suitable for city square and residential area.

Battery Ride On Sweeper YHB16 Technical Parameters:
Model YHB16
Sweeping width 1200 - 1600mm
Suction port width 500mm
Clean water tank volume 150L
Max spraying water capacity 0.8L/Min about 3 hours
Dustbin volume 260L
Dustbin dump height ≥1300mm
Lithium-ion battery 48V /400Amp-hr
Sweeping speed 0-5Km/h
Travel speed 0-25Km/h
Dimension 3650*1300*2110mm

1. When work of automatic floor scrubber is completed, blanket brush or remove floor brush and clean to avoid machine oppression for a long time caused deformation of brush ;

2. With a dry cloth to wipe clean the power cable, and plug the power cord around the well hung on the machine ;

3. Tank cleaning after use - and - drop off, adding half a box of water then water tanks, continued to put out, cleaner crystallization of completely cleaning out water tank valve, or you'll impact caused by water or leak ;

4. With a dry cloth to the fuselage and the bottom of the machine outside the disc, wipe clean ;

5. Machines should be placed in a dry and ventilated place, avoiding moist environment affect the motor and shorten the life ;

6. Empty and clean the sewage tank, during the operation, machine drawing containing sludge - water mixture, they accumulate in vulnerable in a water tank and issued a bad smell, so with a flow of water is necessary for cleaning water tanks ;

7. Empty water tank, especially not when daily cleaning, water will not flow into bacteria and other sources ;

8. Cleaning water filters, sometimes some sediments so as to weaken the effect sucks, use flowing water cleaning filters ;

9. Check that the water Grill is clean ;

10. Weekly checks for brush and wear and tear of grilled water absorption, if the ground is extremely abrasive, strong pressure on the ground will damage them or make them wear faster. Under normal circumstances, brush with 50 hours later, you can replace, on the contrary, after suction rubber uses 30 - hour, it should be replaced or upside down plastic strips tape under the condition of the four sides are still available ;

There are a number of methods you can use to scrub floors, although some are not well-suited for industrial needs. Your grandmother may have used the old-fashioned method of getting down on her hands and knees with a bucket of soapy water and a rag. Over time, products containing a handle like yarn, sponge and removable cloth mops have made the task of scrubbing floors a bit easier, although these methods require a great deal of time, and they are mostly inefficient for cleaning very large floor areas like those found in factories and schools.

Modern technology has introduced more efficient and effective cleaning machines for larger jobs. A walk-behind scrubber, such as the Advantage Adfinity, allows the operator to guide the machine, often without the need to actually push it. These machines combine a cleaning solution at a predetermined dilution level for maximum cleaning efficiency. Walk-behind scrubbers come in a number of scrubbing path widths for a variety of cleaning needs.

For larger floor surfaces, ride-on scrubbers like the Advance 7765 allow operators to clean vast floor areas in a short amount of time, while also offering floor sweeping capabilities. Some units may also dry the floor as they clean, even when operated in tight corners. Riding machines also save wear-and-tear on the operator who does not need to stand or walk for long periods of time. Larger models contain large solution and recovery tanks that allow for extended operation without the need to empty the tanks, which results in even faster completion time.

Using riding floor scrubbers like the Ride On Floor Scrubber YHFS-1200R can be the most efficient and productive way to clean large industrial floors. However, some models can create excess foaming during the cleaning process, which can limit effectiveness and possible harm the machine over time. Some preventive measures can help eliminate the foaming problem.

When filling the solution tank before operation, be sure to put the water in the tank before the detergent. Select a low-foaming detergent and add an industrial defoamer for additional protection against foam. If cleaning an excessively dirty floor, use less detergent instead of more, as extra detergent will mix with the dirty water to create additional foam. Also, pre-washing a heavily soiled floor by driving across it with the machine’s suction turned off and the squeegee blades off the floor will help keep foam to a minimum.

After the cleaning job is complete, be sure to rinse the solution tanks thoroughly to reduce chemical build-up. Over time, the build-up of dried-on chemicals can result in excess foaming when combined with additional cleaning solution. If you use the machine to strip the floors, a thorough cleaning can also remove any chemicals found in the floor wax that can also lead to additional foaming.

In addition to the solution and recovery tanks, it is also necessary to clean any machine parts that come in contact with the cleaning solution to eliminate foaming. Regularly cleaning the machine’s squeegees and float assembly will reduce the build-up of foam-producing chemicals and allow your machine to clean your floors effectively.

Scrubber dryer is often used for cleaning equipment. Proper maintenance can ensure the machine with normal use and extend its life.
    The methods of extend the life of scrubber dryer:
    1 After each cleaning work, the dirt will remain on sewage tank, So it should clean sewage tank usally;
    2 Brush plate and water Grill of scrubber dryer is wearing parts. Periodically review the level of loss weekly in needed. When the multi-function washing machine wear parts relatively large losses should promptly change. Then, it can ensure the ground maintains cleanliness reduce the wear parts of damage to the ground. Generally brush with using 50 hours need replace, Water-absorbing plastic with using 30 hours need replace. Different places is different, So it is based on experience to adjust.
    3 When filter using long time, the dust will deposited on it to block filter. It will reduce the filter's ability to suck. So the filter and connection of grill water sunction pipe is nedd periodically to clean.
    4 The water grill is througn air flow to inhalation of effluent to sewage tank. Every time after you use the washing machine would be grilled sediment deposition in the water around, so every time you use the washing machine while cleaning the suction Grill is very important.

At present, China's economy is fast development phase, the industry is in rapid development, the rapid development of large factories, hotels, shopping centers and other industries, today maintains cleanliness the scale and the sharp rise in traditional human a MOP but a bucket to wash times more real life far away from us.

Not only is the inevitable result is because clean concept of progress when faced with thousands of and even tens of thousands of square of area, our traditional cleaning is so weak. And human resources is increasingly expensive, and customer requirements and further cleaning effect, management more difficult. These social contradictions, mechanized operations is an inevitable trend. However due to cleaning equipment into domestic short, practitioners of professional idea is bad, just want to sell equipment to the customer, without truly understanding customer needs, making markets generally believe that washing machines use costly, not fundamentally for customers to reduce costs, improve enterprise values.

Chaos and disorder in the scrubber dryer market, and our customers love and hate washing machine, and can only be kept at. But as the industry standard, professional level of employees is constantly improving, machine use of more humane, as long as the targeted training to customers, customers can quickly grasp and use the scrubber dryer.

With economic development, will bring to cleaning equipment has broad application prospects, property and building of the year, and other places with large area needs to be cleaned for the scrubber dryer of this type of cleaning equipment to add a broad market space.

Scrubber dryer valve sink too large or too small do has an impact on engine working? Its valve sink over that will reduce compression ratio. Move at the same time as the valve with valve bomb praise of spring elasticity decrease.

Lax slow valve closing or closed, the engine starting difficulties, power reduction, increased consumption : menxiatao through small, increases the compression ratio, gross engine work, make parts too large, reduce the work and life can be made of serious also possible piston blow valve, causing damage to the piston and valve train related parts.

In use should be based on wear of valve and valve seats, to check the valve sinkage, a settlement over the time to replace the valve or valve seats ; after swapping the new valve or valve seats, valve subsidence through small, may be appropriate to mill grinding valve seat and valve.